亚亚洲欧洲精品,日韩中文视频,亚洲国产精品久久久久秋霞蜜臀

聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

新聞資訊

雕刻機工作過程中出現突發情況如何處理？

來源：http://www.tj9.net 時間：2021-02-20

雕刻機在工作過程中難免會有些突發情況，如：雕刻刀斷掉了，雕刻材料移動了等等，都需要終止雕刻，重新開始。對于一些復雜的路徑要是再重頭開始，不免要浪費很多時間，這里就來五軸保麗龍雕刻機廠家說一下應對這些問題的方法。

Carving machine in the process of work will inevitably have some unexpected circumstances, such as: carving knife broken, carving material moved, etc., need to stop carving, start again. For some complex paths, if we start all over again, it will inevitably waste a lot of time. Here are the methods to deal with these problems by the five axis styrofoam engraving machine manufacturers.

1 終止雕刻：對于一些二維或是三維路徑都比較復雜，用時比較長，要是在雕刻過程中刀具斷掉，要暫停雕刻機（維宏系統快捷鍵F10）然后再終止雕刻（F11)關閉主軸旋轉。

Stop engraving: some 2D or 3D paths are complicated and take a long time. If the cutter breaks during engraving, first stop engraving machine (shortcut key F10 of Weihong system), then stop engraving (F11) and turn off spindle rotation.

2 回工件原點：使雕刻機回到工件原點（快捷鍵F7)，上升機頭，更換刀具，刀具直徑一定要跟之前使用的一樣，否則會影響雕刻效果。

2 return to the workpiece origin: make the engraving machine return to the workpiece origin (shortcut key F7), raise the head, change the tool, the tool diameter must be the same as before, otherwise the engraving effect will be affected.

3 重新設定Z軸原點：接著就開啟主軸，設定Z軸的深度（要跟之前的設定方式一致，臺面對刀或工件對刀）

Reset z-axis origin: then open the spindle and set the depth of z-axis (same as the previous setting method, tool setting on table or workpiece)

4 執行開始：點擊操作–開始，選擇從“具體位置到文件結束”具體位置是指之前終止文件的地址，在主軸旋轉按鈕左側顯示，一般選擇時要小于當前數字，這樣不于漏刻。點擊確定就可以了。

4. Execute advanced start: click operation - Advanced start, and select "specific location to end of file". The specific location refers to the address of the previous terminated file, which is displayed on the left side of the spindle rotation button. Generally, the selection should be less than the current number, so as not to miss engraving. Just click OK.

分解路徑

Decomposition path

1 重新計算路徑：如果雕刻的文件是由多個整體路徑組成的，那么在發生突發情況后，可以在文泰里把已經雕好的路徑刪除，只保留未雕刻的路徑，然后重新保存路徑。

1 recalculate path: if the carved file is composed of multiple overall paths, then in case of emergency, you can delete the carved path in Wentai, keep only the uncut path, and then save the path again.

2 重新開始新的雕刻文件：換上新的刀具并設定好Z軸原點后，（注意X\Y軸原點不能修改）選擇新的雕刻文件，來雕刻未完成的部分即可。

2 start a new engraving file again: after changing a new tool and setting the z-axis origin, (note that the x-axis and y-axis origin cannot be modified), select a new engraving file to carve the unfinished part.

注意事項在更換刀具后一定記得重新設定Z軸深度，不然很能下刀過深導致刀具斷掉。

Note: remember to reset the z-axis depth after changing the tool, otherwise the tool will be broken due to too deep cutting.