在使用雕刻機的時候，須知一定的安 全知識，而且可能由于操作不當或者維護不當導致一些新問題產生，那么改如何檢驗泡沫雕刻機機箱呢?要知道檢驗泡沫雕刻機機箱可預防一定的問題出現，提高泡沫雕刻機的使用壽命.下面一起去看看吧.

When we use the engraving machine, we need to know certain safety knowledge, and may cause some new problems due to improper operation or improper maintenance. Then how do we test the foam carving machine case? We should know that testing the foam engraving machine box can prevent certain problems and improve the service life of the foam engraving machine.

1.機箱里的電纜線不允許有凌亂的現象.

1. The cables in the case are not allowed to be messy

2.機箱的線號要整齊，線號一定齊全(各線端頭處都應有相應的線號);線是否壓好，有沒有銅絲露在外面.

2. The wire number of the chassis should be neat and complete (there should be corresponding wire number at the end of each wire); Whether the wire is well pressed and whether the copper wire is exposed

3.機箱標識是否貼全、貼正;各個部分是否已打掃干凈;保證沒有雜物，金屬屑等雜物.

3. Whether the chassis identification is fully and correctly pasted; Whether all parts have been cleaned up; Make sure there are no sundries, metal scraps, etc

4.變壓器﹑變頻器﹑驅動器的接觸器的是否留有余量，這些地方的線不宜太緊，否則會影響線的使用壽命，數控保麗龍雕刻機廠家，線可以彎90°的弧度，在床身下面安裝的變頻器進線和出線分別要用纏繞管纏繞，在床身上打孔穿線時一定加護套.

4. Whether the contactor of transformer, frequency converter and driver has allowance, the wire in these places should not be too tight, otherwise it will affect the service life of the wire. For CNC styrofoam engraving machine manufacturers, the wire can be bent for 90 ° The inlet and outlet of frequency converter installed under the bed should be wound with winding pipe respectively, and the sheath must be added when drilling holes on the bed

5.維宏、DSP系統等進機箱的數據線是否固定好(可用管卡固定)，否則會數據線插頭插針拉壞;DSP/維宏系統的數據線是否用卡子固定;有3.0KW以上的變壓器底面一定加加厚平墊背母，是否加了.

5. Whether the data cable of Weihong and DSP system into the chassis is fixed (it can be fixed with pipe clamp), otherwise the plug pin of the data cable will be damaged; Whether the data line of DSP / macro system is fixed with clip; If there is a transformer above 3.0kw, the bottom surface must be thickened

6.機箱的開關一般固定在機箱的頂部，開關線一定用纏繞管纏好，大型保麗龍雕刻機廠家，不能有凌亂現象;面板周圍是否有膠影響機箱的外觀.

6. The switch of the case is generally fixed on the top of the case, and the switch wire must be wrapped with winding tube. Large styrofoam engraving machine manufacturers should not be messy; Whether there is glue around the panel affects the appearance of the chassis

雕刻機的應用范圍及日常維護保養雕刻從加工原理上講是一種鉆銑組合加工，雕刻機多種數據輸入模式根據需要游刃有余。因為雕刻機的應用范圍非常廣泛，因此有必要了解各種雕刻機的的應用范圍。小功率的只適合做雙色板、建筑模型、小型標牌、三維工藝品等。由于功率太小而大大影響了其應用的范圍。大功率雕刻機可以做小功率雕刻機的東西。適合做大型切割、浮雕、雕刻。

Engraving machine application scope and daily maintenance engraving from the processing principle is a combination of drilling and milling processing, engraving machine a variety of data input mode according to the need. Because the application range of engraving machine is very wide, it is necessary to understand the application range of various engraving machines. Low power is only suitable for two-color boards, building models, small signs, three-dimensional crafts, etc. Because the power is too small, its application range is greatly affected. High power engraving machine can be used for small power engraving machine. Suitable for large cutting, relief and carving.