聯系我們
18560023440
王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間
業內資訊
雕刻機的檢修方法有哪些？
來源：http://www.tj9.net 時間：2022-03-09
保麗龍數控雕刻機為高精數控設備，雕刻機不能正常工作時，可能是其內部元件出了問題或者是其他方面的原因，所以必要的日常維護與保養對本機的使用壽命及精度關重要，下面來看下雕刻機的檢修方法有哪些呢?
Baolilong CNC engraving machine is a high-precision CNC equipment. When the engraving machine fails to work normally, there may be problems with its internal components or other reasons. Therefore, the necessary daily maintenance and repair are very important to the service life and accuracy of the machine. What are the maintenance methods of the engraving machine?
1、確定雕刻機的電壓是220伏還是380伏，不可盲目載電。
1. First, determine whether the voltage of the engraving machine is 220 V or 380 V, and do not carry electricity blindly.
2、確定電壓是否符合要求，電壓應在210V-230V之間，如果不符合需要采用穩壓器。選擇穩壓器時一定要選擇高質量的(功率在2000W以上，一般重量應在15公斤以上)。
2. Determine whether the voltage meets the requirements. The voltage should be between 210v-230v. If it does not meet the requirements, a voltage regulator needs to be used. When selecting a voltage regulator, you must choose a high-quality one (the power is more than 2000W, and the general weight should be more than 15kg).
3、雕刻機需要要接地線，一是保證機器的使用，另一個是避免靜電干擾。
3. The engraving machine needs to be grounded. One is to ensure the use of the machine, and the other is to avoid electrostatic interference.
4、雕刻機屬于數控設備，切不可隨意拆卸及在不懂的前提下調節電器配件，尤其是變頻器。
4. Engraving machine belongs to numerical control equipment. It must not be disassembled at will and adjust electrical accessories without understanding, especially frequency converter.
5、雕刻機要長保養，保證機器的潤滑、經常除塵等;保持導軌、絲杠的干凈，潤滑。
5. The engraving machine shall be maintained for a long time to ensure the lubrication and frequent dust removal of the machine; Keep the guide rail and lead screw clean and lubricated.
6、械，雕刻主軸電機，一定要保證循環水系統通暢，做好主軸的降溫。
6. Machinery, engraving spindle motor, we must ensure that the circulating water system is unobstructed and do a good job in cooling the spindle.
7、主軸電機保護：如果出現雕刻電機停轉的情況或電機轉速不勻的情況，請立即切斷電源并與我廠維修。如果在電機停轉的情況下電機是不能加電的，否則電機的經圈會馬上燒掉，請用戶使用時一定注意。
7. Spindle motor protection: if the engraving motor stops or the motor speed is uneven, please cut off the power supply immediately and repair with our factory. If the motor stops running, the motor cannot be powered on, otherwise the warp ring of the motor will be burned immediately. Please pay attention to it when using it.
8、卡頭的保護：電機卡頭和刀具之間是靠金屬的摩擦固定的，所以安裝刀具加油，防止長時間不拆卸或冷卻液腐蝕而造成拆卸困難。
8. Protection of clamp head: the motor clamp head and the cutter are fixed by metal friction, so the cutter is installed for refueling to prevent the difficulty of disassembly caused by long-term non disassembly or coolant corrosion.
所以一定要嚴格按照上述要求進行。萬萬不可掉以輕心。
Therefore, we must strictly follow the above requirements. Never take it lightly.
以上就是為大家介紹的有關保麗龍雕刻機的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.tj9.net/
The above is a detailed introduction to the poly dragon engraving machine. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.tj9.net/
- 上一篇：保麗龍雕刻機值得購買嗎？
- 下一篇：數控雕刻機的電主軸功率怎么選擇呢?
