聯系我們
18560023440
王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間
新聞資訊
雕刻機的圓刀和平刀有什么不同
來源：http://www.tj9.net 時間：2021-04-09
雕刻機的刀具分為園刀和平刀，兩種刀具在外形上有很大不同，功能上也是各有特點，下面就為您介紹這兩種刀具，方便日后您的選擇。
The cutter of engraving machine is divided into round cutter and flat cutter. The two kinds of cutters are very different in appearance and have their own characteristics in function. The following is to introduce these two kinds of cutters for your convenience in the future.
雕刻刀的圓刀：
Round knife of carving knife:
刃口呈圓弧形，多用于圓形和圓凹痕處，在雕刻傳統花卉上也有很大用處，如花葉、花瓣及花枝+的圓面都需用圓刀適形處理。 圓刀橫向運刀比較省力，對大的起伏圓刀橫向運刀比較省力，對大的起伏、小的變化都能適應。而且圓刀的線條不肯定，使用起來靈活且便于探索。
The cutting edge is arc-shaped, which is mostly used for round and round dent. It is also very useful in carving traditional flowers. For example, the round surface of flower leaves, petals and branches need to be shaped with a round knife. It's easier to move the round knife horizontally. It's easier to move the round knife horizontally for large fluctuation. It can adapt to large fluctuation and small change. And the line of round knife is not sure, so it is flexible and easy to explore.
根據不同的用途，圓刀的型號應有所區別，大小范圍基本在5厘米一0.5厘米之間。做圓雕人物的刀口兩角要磨去，呈圓弧形，否則雕衣紋或其它凹痕時，不但推不動，還會破損凹痕道的兩旁。
According to different uses, the models of round knives should be different, and the size range is basically between 5cm and 0.5cm. The two corners of the knife edge should be polished off to form a circular arc. Otherwise, when the pattern or other dent is carved, it will not only be unable to push, but also damage both sides of the dent road.
倘若做浮雕時，則應保留刀口兩角，并利用其角尖的功能雕刻地子角落處，因此要配備二種。圓刀還有正反之別，斜面在槽內、刀背呈挺直的為正口圓刀，它吃木比較深，更適合做圓雕，尤其是在出坯和掘壞階段。
If you do relief, you should keep the two corners of the knife edge, and use the function of the corner to carve the corner of the floor, so you should have two kinds of relief. There are also positive and negative aspects of the round knife. The one with the inclined plane in the groove and the straight back is the round knife with positive mouth. It eats wood deeply and is most suitable for round carving, especially in the stage of casting and digging.
雕刻機平刀：
Engraving machine flat knife:
刃口呈平直，主要用于劈削鏟平木料表而的凹凸，使其平滑無痕。型號大的也能用來鑿大型，有塊面感，運用得法，如繪畫的筆觸效果，顯得剛勁有力，生動自然。平刀的銳角能刻線，二刀相交時能剔除刀腳或印刻圖案。瑞典和蘇聯的木雕人物就多用平刀，有強烈的木趣刀味。
The cutting edge is straight, which is mainly used to split and level the concave and convex of wood surface, making it smooth and traceless. Large models can also be used to chisel large, block surface feeling, the use of appropriate, such as painting brush effect, appears strong, vivid and natural. The sharp angle of the flat knife can cut lines, and when two knives intersect, the knife foot or the printed pattern can be eliminated. In Sweden and the Soviet Union, the wood carving figures usually use flat knives, which has a strong taste of wood.
- 上一篇：怎樣解決雕刻機的突發情況
- 下一篇：石材雕刻機的總體結構和原理是什么？
