av资源中文在线,日本国产欧美色综合,天堂社区日本电影超碰

聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

新聞資訊

數控開料機主軸使用以及維修保養方法!

來源：http://www.tj9.net 時間：2021-10-18

1.軸承選用C級高速角觸摸軸承本產品NSK軸承。

1. Class C high-speed angle touch bearing is selected as the bearing. NSK bearing of this product.

2.選用精度鋼球堅持器，這樣確保了電主軸在高速磨削時的反轉精度。

2. The precision steel ball holder is selected to ensure the reverse accuracy of the motorized spindle during high-speed grinding.

3.電主軸外殼冷卻選用液循環冷卻，降低高速旋轉引起的發熱溫升。

3. The motorized spindle shell is cooled by circulating coolant to reduce the heating temperature rise caused by high-speed rotation.

4.電主軸選用油霧光滑，選用油脂光滑。

4. The motorized spindle shall be smooth with oil mist and grease.

運用方法

Application method

1.開機前有必要接上油水管，做到電主軸先接通油水管后再發動主軸電機，安裝時水管油管不能接錯。主軸左右兩頭為水管，中間為油管(數控鉆銑床主軸是油脂光滑，不選用以上方法。)

1. Before startup, it is necessary to connect the oil water pipe, so that the motorized spindle can be connected with the oil water pipe first, and then start the spindle motor. During installation, the water pipe and oil pipe can not be connected incorrectly. The left and right ends of the spindle are water pipes and the middle is oil pipes (the spindle of NC drilling and milling machine is smooth with grease, so the above method is not selected.)

2.運用電主軸時應先接油霧管點，管點接頭應清潔凈，防止污物進入形成軸承燒壞。操作時應看電主軸前端部稍有油霧泄出后，才干發動電主軸，油霧光滑主張選用5號主軸油調理，進油管為20-30滴/分，常常查看不能斷油，不然會形成主軸損壞。

2. When using the motorized spindle, the oil mist pipe point shall be connected first, and the pipe point joint shall be clean to prevent dirt from entering and burning the bearing. During operation, the motorized spindle can be started only after the oil mist at the front end of the motorized spindle leaks out slightly. The oil mist is smooth. It is recommended to use No. 5 spindle oil for conditioning. The oil inlet pipe is 20-30 drops / min. it is often checked that the oil cannot be cut off, otherwise the spindle will be damaged.

3.操作時，有必要做到主軸徹底停止轉動后，才封閉油霧，這樣才干延長運用壽命，說明發動不宜過火頻頻。

3. During operation, it is necessary to close the oil mist after the main shaft completely stops rotating, so as to prolong the service life, indicating that the engine should not be started too frequently.

4.電主軸運用前有必要查看砂輪接桿是否同軸，如不同軸超過0.03毫米應還砂輪接桿，不然既損壞電主軸，又磨欠好作業，磨削時應留意不要碰擊，應校正后再進去磨削。

4. Before using the motorized spindle, it is necessary to check whether the grinding wheel connecting rod is coaxial. If it is not coaxial more than 0.03mm, return the grinding wheel connecting rod, otherwise the motorized spindle will be damaged and the grinding operation will not be good. During grinding, pay attention not to bump, and go in for grinding after correction.

維修保養

Maintenance

1.電主軸所接中頻電源額外電壓，頻率應與電主軸技術參數相符，電主軸轉速能夠改動頻率來調正，一起電壓也成正比改動。

1. The frequency of the additional voltage of the medium frequency power supply connected to the motorized spindle shall be consistent with the technical parameters of the motorized spindle. The speed of the motorized spindle can be adjusted by changing the frequency, and the voltage is also changed in direct proportion.

2.運用過程中應防止電主軸軸端部與工件發生意外碰擊。

2. During operation, the end of the motorized spindle shaft shall be prevented from accidental collision with the workpiece.

3.運用過的電主軸暫不必，使用壓縮空氣吹清水管內冷卻液，避免生銹，阻塞小孔。并在外表涂上防銹油、軸端加保護裝置放于干燥處保存。

3. The used motorized spindle is not necessary temporarily. Use compressed air to blow the coolant in the clean water pipe to avoid rust and blocking the small hole. The surface shall be coated with anti rust oil, and the shaft end shall be protected and stored in a dry place.

4.應盡量削減空工作，開機前應查看進出冷卻水石非疏通。

4. Empty work shall be reduced as far as possible, and the inlet and outlet cooling water shall be checked before startup.